Skip to content
Icon
Calculate the Material Required

Vacuum Chamber

Original price $174.95 - Original price $174.95
Original price
$174.95
$174.95 - $174.95
Current price $174.95
Availability:
in stock, ready to be shipped
Document

The ArtMolds Vacuum Chamber is designed for deairing (eliminating air bubbles) in appropriate pot life resins and silicones. Vacuum Chamber with vacuum pump combination only $299.95

Description

Vacuum Chamber. Take the next step in studio equipment by adding that important vacuum chamber. To assure bubble-free mold rubber when mixing polyurethane and silicones, a vacuum chamber is required. The low cost ArtMolds' Vacuum Chamber is the perfect addition to the small studio, school, university or protype lab. The ArtMolds' Vacuum Chamber has been engineered  for deairing (eliminating air bubbles) mold making and casting rubbers. Though the price point of our vacuum chamber may be low, its design does not skip on prefessional grade quality -- and safety.

This PVC vacuum chamber, along with ½-inch opitically clear acrylic plates make a safe and efficient unit. The vacuum chamber includes all machined brass fittings, including a  pet cock exhaust valve, hose barb to connect your vacuum pump, a vacuum gauge, a pair of matched rubber gaskets, and a set of ½-inch clear acrylic plates. All you need is a vacuum pump for your new vacuum chamber that will pull 29-inches of mercury (Hg) at sea level, needed to deair your materials.


Vacuum Chamber Specifications:

Capacity:                4-gallon vacuum chamber (approximately)

Dimensions:          10-inch diameter by 10-inch tall

Maximum Pull:       29-inches of mercury (Hg) at sea level
                              24-Hg at elevation of Denver, CO

Weight:                  20-pounds / Shipping weight 22-pounds

Package Size:        12" x 12' x 12"

Vacuuming Process:

Mix your rubber according to the manufacturers directions. Use a container that holds at least four times the amount of material you are vacuuming to allow for the expansion of the material. Once your vacuum chamber reaches 29-inches of mercury (at sea level), the material will begin to rise (resembling foam) for a minute or two. When the material falls it will plateau and not rise any more. You will want to continue opertaing the vacuum chamber for another 2-3-minutes to make certain all of the air has been removed from your material. Open the petcock of your vacuum chamber to allow air inside, remove your material from the vacuum chamber. Pour the material slowly starting from the corner of the mold box, or mold, letting the material to flow freely into the box or mold cavity. This method will usually not introduce any new bubbles into the vacuumed material. To insure that the material is totally devoid of air bubbles you can place the entire mold/mold box into the chamber for an additional few minutes. This will assist the material into difficult areas of the mold/mold box.

 
Assembly Instructions:
  • Thread your gauge onto the brass fitting that will attach to the vacuum chamber
  • Thread your gauge onto the brass fitting that will attach to the vacuum chamber
  • Take the assembled fitting with gauge and thread it into the side of the vacuum chamber
  • Place the Lexan plates on flat surface
  • Place one of the red gaskets in the center of the Lexan plates
  • Place it on the PVC cylinder / Vacuum Chamber evenly in the center of the gasket
  • The second red gasket is placed on the top of the vacuum chamber
  • The second Lexan plate will be placed over that gasket to seal your Vacuum Chamber
  • Connect the tube to your vacuum source

    Download Owner's Manual Here

    Download Technical Bulletin

    DownLoad Independent Vacuum Chamber Test
CAUTION: PLEASE TAKE SAFETY PRECAUTIONS WHEN USING YOUR VACUUM CHAMBER. Always wear safety glasses, no close or prolonged viewing through Lexan plate. Never use the Lexan plate as a cutting

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)

Related Categories